MP250 5B00 Error On Canon MP Series Printer - 5B00 FIX CANON

MP250  5B00 Error On Canon MP Series Printer




Etiketler: ,

CANON PRINTER CARTRIDGE RESET

Reset Printer Canon MP140, MP160, MP180, MP210, MP220, MP460, MP470, MP500, MP510, MP520, MP530, MP600, MP610, MP800, MP820, MP810, MP830, MP960, MP970
Reset Canon MP140

 BU TUŞA 30 SN BASILI TUTUN KARTUŞLAR RESETLENMİŞ OLACAK 
 

THIS BUTTON 30 SECCOND PRESS - CARTRIDGE RESETT


Reset methode on canon MP145 work also on MP140, you can read the methode here: reset waste ink counter canon pixma mp145
Reset Canon Pixma MP160, Mp180, MP460
To reset the printer model you can use MPtool software, the reset methode can be found here: reset canon pixma mp160, mp170, mp180 and mp460 using mptool software. But before using MPTools software you must read this comment to reset our printer without error.
Reset Waste Ink Counter Canon Pixma MP210 and Canon Pixma MP220
  1. Start with printer off
  2. Press and hold resume Button (triangle in the circle) and click “Power” button. green led should be on
  3. hold the Power button, release Resume Button.
  4. Without releasing the Power Button, double click “Resume” button and then release Both Buttons.
  5. Click “Resume” for four times then click “Power” button, to confirm the selected action (reset counter absorber).
  6. Turn off the printer and turn on again
Reset Ink Level Canon Pixma MP460 (Manual Methode)

  1. Disconnect the power cable
  2. Hold down power button
  3. Reconnect the power cable
  4. With the power button still down, press twice the “Cancel/Stop” red button
  5. Release the power button
  6. The printer is now in factory mode…(wait about 30 seconds until it says “idle”)
  7. Press the down arrow (next to the “OK” button) until it says “Shipping Mode 1”
  8. Press the “OK” Button
  9. Now with it displaying “Without Cleaning” press the power button
  10. A test page should print
  11. Now open cover
  12. Disconnect the power again
  13. Take both cartridges out like normal
  14. Close cover
  15. Reconnect power cable
  16. Press power button
  17. Replace cartridges
note: Other methode to reset ink level you can use MPtool software
Reset Ink Level Canon MP470
It is basically a modified reset procedure for Canon MP460.
  1. Disconnect the power cable.
  2. Hold down On/Off button.
  3. Reconnect the power cable.
  4. With the power button still down, press the Stop/Reset button twice.
  5. Release the On/Off button.
  6. The printer is now in factory mode (wait until idle is displayed)
  7. Press the right arrow button (next to the OK button) repeatedly until Shipping Mode 3 is displayed.
  8. Press the OK Button
  9. Wait until “Without Cleaning” is displayed and then presss the Stop/Reset button once.
  10. A test page should print.
  11. Open the cover. (the cartridges should position themselves at the far left – the cartridge removal location)
  12. Disconnect the power cable.
  13. Remove both cartridges.
  14. Close the cover.
  15. Reconnect the power cable.
  16. Press the On/Off button.
  17. Wait until a Replace Cartridges message is displayed. Now insert the cartridges.
  18. Wait until the printer is operating in its normal mode. The display shows the normal start menu (ie: Copy).
to view the Ink level
  • Check by going to printer ->properties -> maintenance -> view printer status
Reset Canon Pixma MP520 maybe Work Also on Canon MP500, MP510 and MP530

To reset Canon Pixma MP520 view this article: Resetting Canon Pixma MP520
Reset Methode for Canon MP600, MP610, MP800, MP820, MP810, MP830, MP960, MP970 was removed by admin because doesn’t work
Note: Some of the reset method has update on April 20, 2010
Etiketler:

Lexmark Printers -- Lexmark Reset Methods - Lexmark All Printer Resett

Lexmark Printers -- Lexmark Reset Methods

lexmark reset methods
Refill your own Lexmark inkjet cartridges with our easy-to-use refill kits
LaserPrinter 10R/10 Plus, 12 Series, 16 Series, Optra R & L
1. Turn the printer off
2. Enter the Diagnostics Mode by holding down the READY and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST
3. Select MAINTENANCE COUNT
4. Select RESET to return the count to zero
5. Press the RETURN button to return to the Diagnostics Mode main menu, then reset printer to return to normal mode
Optra S, 2420/2450/2455/3455
1. Turn the printer off
2. Enter the Diagnostics Mode by holding down the GO and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. When ready, the display will read PRINT REGISTRATION
3. Scroll to PRINTER SETUP and press the SELECT button
4. Scroll to MAINTENANCE PAGE COUNT and press the SELECT button
5. Scroll to RESET MAINTENANCE COUNT and press the SELECT button to reset the count to zero
6. Press the RETURN button to return to the Diagnostics Mode main menu, then exit Diagnostics Mode to return to normal mode
Optra T (all models)
1. Turn the printer off
2. Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test, the display will read CONFIG MENU
3. Press the right arrow side of the MENU button until MAINTENANCE PAGE COUNT is on the display
4. Press the SELECT button. RESET should be displayed
5. Press the SELECT button again to reset
6. Press the RETURN button to return to the Configuration Menu and press the left arrow side of the MENU button to exit the Configuration Menu
Optra W810
1. Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test the display will read CONFIG MENU
2. Press the right arrow side of the MENU button until MAINT. COUNTER is displayed
3. Press the SELECT button, then scroll to RESET TRANSFER or RESET FUSER and press the SELECT button again to reset
4. Press the RETURN button to return to the Configuration Menu and press the left arrow side of the MENU button to exit the Configuration Menu
Optra C710
1. Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test the display will read CONFIG MENU
2. Press the MENU button right or left until RESET FUSER COUNT appears
3. Press the SELECT button to reset the count
Optra C720
1. Enter the Diagnostic Menu for all resets by pressing the GO and RETURN buttons and turn the printeron
2. Continue holding until PERFORMING SELF TEST is displayed
3. Select RESET COUNTERS from the Diagnostic Menu
4. Select the individual counter for reset and press the SELECT button
Optra C750
1. Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test, the display will read CONFIG MENU
2. Select individual reset for fuser or ITU kit
Optra SC 1275/Color 1200
1. Turn the printer off
2. Hold down the GO and RETURN keys while powering on the printer until PERFORMING SELF TEST is displayed
3. When REGISTRATION is displayed, press the right side of the MENU key six times until MAINTENANCE is displayed
4. Press the SELECT button, and then press the right side of the menu button to scroll to 80 or 81 RESET
5. Press the RETURN button until the display reads MAINTENANCE
6. Press the right side of the MENU button until the display reads EXIT DIAGNOSTICS
7. Press the SELECT button to return to the normal mode
Reprinted with permission from laser-service.com
Etiketler:

OKI B430 MENU RESET- TONER RESET- CHIP RESET - FIX FIRMWARE OKI DATA PRINTER



1-YAZICIYI KAPAT
2-YUKARI VE AŞAĞI TUŞLARINA BASILI TUTUP YAZICIYI AÇIN
3-EKRANDA "OKIUSER" YAZANA KADAR BEKLEYİN
4-YUKARI + AŞAĞI TUŞLARINI BIRAKIN
5-" Engine Dialog Mode" YAZAN MENÜYE GELİN
6-"Reset engine" YAZAN YERE GELİN
7-ENTER A BASIN



1) Turn off printer.
2) Hold down "+" and "-" buttons at the same time, and keep them held down while turning printer back on... continue to hold until the word "OKIUSER" appears.
3) Use "-" button to scroll down to "FUSE KEEP MODE".
4) Press "Enter" button, hold for approx. 10 seconds, then release.
5) Press "Enter" button again, followed by rapid release and repress with hold for approx. 10 seconds.
6) Release "Enter" button, then press and let up one more time quickly.
7) You will see "INITIALING" and then "ONLINE" messages.


1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4.Scroll down to "Reset engine".
5.Press Enter button.
Etiketler: ,

BROTHER HL-2130 TONER RESETTER - HL-2130 RESET MENU TONER RESET - CHIP RESET - FIX FIRMWARE




MUTLakA OKUYUNUZ....

GÜÇ DÜĞMESİNİ KAPATIP GO DÜĞMESİNE BASILI TUTUNUZ.
TONERİN KONULDUĞU ÖN GİRİŞ KAPAĞINI AÇINIZ.
Güç düğmesini açın ve tüm ışıklar yandıktan sonra GO düğmesini bırakın.
Ardından GO düğmesine 2 kez art arda basıp bırakın.
Tüm ışıklar yanıncaya kadar bekleyin.Tüm ışıklar yanınca 6 defa GO düğmesine art arda basın.
Bekleyip ön kapağı kapatın.
Toneriniz tekrar dolu gösterecektir.



YUKARIDAKİ İŞLEMLERİ TONER BİTMEDEN DE YAPABİLİRSİNİZ.HER DURUMDA TONER RESETLENEBİLMEKTEDİR.
DEMO TONERE PARÇA SATIN ALMANIZA GEREK YOKTUR.TECRÜBEYLE ÖLÇÜLMÜŞTÜR.
Etiketler: ,

BROTHER HL-2040 MENU RESET TONER RESET - CHI PRESET FREE FIX TONER RESET

BROTHER HL-2040 MENU RESET TONER RESET - CHI PRESET FREE FIX TONER RESET

MUTLakA OKUYUNUZ....

GÜÇ DÜĞMESİNİ KAPATIP GO DÜĞMESİNE BASILI TUTUNUZ.
TONERİN KONULDUĞU ÖN GİRİŞ KAPAĞINI AÇINIZ.
Güç düğmesini açın ve tüm ışıklar yandıktan sonra GO düğmesini bırakın.
Ardından GO düğmesine 2 kez art arda basıp bırakın.
Tüm ışıklar yanıncaya kadar bekleyin.Tüm ışıklar yanınca 6 defa GO düğmesine art arda basın.
Bekleyip ön kapağı kapatın.
Toneriniz tekrar dolu gösterecektir.
ANCAK TOZ BİTMİŞSE dolum için 80gr toz satın alın,2500 sayfaya kadar çıktı alabilirsiniz.

YUKARIDAKİ İŞLEMLERİ TONER BİTMEDEN DE YAPABİLİRSİNİZ.HER DURUMDA TONER RESETLENEBİLMEKTEDİR.
DEMO TONERE PARÇA SATIN ALMANIZA GEREK YOKTUR.TECRÜBEYLE ÖLÇÜLMÜŞTÜR.



1. turn the printer off yazıcıyı kapatın
2 . 2. check that the front cover is open Ön kapak açık olup olmadığını kontrol edin
3 press and hold the go button and while holding turn the printer on . 3 go düğmesine basın ve basılı tutun ve tutarken yazıcıyı açın.
4.check that the toner/ drum/paper / leds are all on . Toner / drum / kağıt / led bütün olduğunu 4.check.
5 . 5.. release the Go button and check that all LED go out. Go düğmesini bırakın ve tüm LED dışarı çıkmak olmadığını kontrol edin.
6 Press the go button twice . 6 kez go düğmesine basın.
7 Check the toner / drum/paper Led are now on 7 Led toner / drum / kağıt Check bulunur
8 Press the go button six times 8 go düğmesine altı kez basın
9 close the front cover . 9 ön kapağı kapatın.
Etiketler: ,
Kaydol: Kayıtlar (Atom)